Friday, October 19, 2018

Epson stylus nx300 Wireless Printer Setup, Software & Driver

      Epson stylus nx300 Wireless Printer Setup, Software & Driver

 Epson stylus nx300 Wireless Printer Setup, Software & Driver
Epson stylus nx300 Wireless Printer

Wireless/Wifi/WPS Connection set-up Guide For epson stylus nx300

Before we start, there are however some conditions that must be met in order to use the WPS pushbutton method:

The access point must have a physical WPS push button available, please check with your device’s user guide for details.
Ur network must be using the WPA (Wi-Fi Protected Access) or WPA2 security protocol. Most WPS enabled access points will not connect using the WPS method if the WEP (Wired Equivalent Privacy) security method is used, or if no security is enabled. For details on which security method is being used on your wire-less network, please check the wire-less connection settings on your computer.

Please follow the steps below to complete the set-up
-->-->-->Step to 1
Make sure the wire-less router is in range of the printer & the WPS button is ready to be pressed.

-->-->-->Step to 2
Press & hold the (Wireless) button (A) on the printer until the wire-less lamp (B) flashes.

-->-->-->Step to 3
Press the (Colour) button (C).

-->-->-->Step to 4
Press the (Wireless) button until the Direct lamp (D) lights up.

-->-->-->Step to 5
Press the (Colour) button, & make sure that the ON lamp (E) & the wire-less lamp flash, then press the (WPS) button on the wire-less router within 2 minutes. The blue WiFi lamp on the printer will continue to flash while searching, & the Power & WiFi lamps will flash when connecting to the access point.

-->-->-->Step to 6
When the printer has successfully made a connection to your wire-less network, the Power & WiFi lamps will stop flashing & remain lit. The network lamp will also light up.
For exact details regarding pressing the WPS button, please refer to the access point manual.

Network settings confirmation

To confirm that your printer is successfully connected to your wire-less network, u can print out the network settings of your printer if u wish:
  • Make sure that your printer is turned on.
  • Load a sheet of A4 or Letter-sized plain paper. 
  • Press & hold the (Wi-Fi) until the WiFi lamp flashes once, & then release it. 
  • Press the (Colour)
  • Press the (Wi-Fi)
  • Press the (Colour)
The network information page will be printed.
When referring to the printout, check that “Connection” indicates “Active” & that the SSID -Service Set Identifier (the name of your wire-less network) indicates the correct name of your wire-less network.

This concludes the WPS set-up procedure.
Please now install the provided software.


If u do not have the CD(’s) that came with your product, or u're a Mac user, please Download the software on Site.

--------------------------------------------------------------------------------------------------------------------------

Standard Connection Method (For Windows & Mac users only)

If your access point does not support the WPS feature, use the following instructions to set your printer up on your wire-less network:
For Windows users, insert the CD that came with your printer & runs the setup.
If u do not have a CD drive, or you're a Mac user, then please download the software.

Connection for Windows Users Only

-->-->-->Step to 1
Double-click on the downloaded .exe file to open the following screen & click (Start Setup).

-->-->-->Step to 2
The software will check to see if there are any updates to the driver & software. This may take a few minutes to complete.

-->-->-->Step to 3
Select your region & country, then click (Next).

-->-->-->Step to 4
If u accept the terms of the license agreement, click (Yes).

-->-->-->Step to 5
If u would like to take part in the extended survey program, click (Agree).
Otherwise, click (Do not agree).

-->-->-->Step to 6
Ensure (Deactivate the block) is checked & click (Next) .

-->-->-->Step to 7
The following screen will be displayed for a few seconds.

-->-->-->Step to 8
Select (Wireless LAN Connection) & click (Next) .

-->-->-->Step to 9
Ensure that your printer is powered on & click (Next).

-->-->-->Step to 10
The software will search for any printers already set up on your network.

-->-->-->Step to 11
If u have already connected your printer to your network, select it from the list & click (Next) to start the software installation, then proceed to.

-->-->-->Step to 16 . 
If u cannot see your printer listed, continue to -->-->-->Step to 12.

-->-->-->Step to 12
If this is the first time you're setting up your printer, it will not be displayed in the list.
Ensure (Set up the network connection according to the guide) is selected & click (Next).

-->-->-->Step to 13
The set-up guide will open & guide u through connecting your printer to your network using the easy wire-less connect process.
Please follow the on-screen instructions carefully to prepare your printer for connection.
Only click next, when your printer corresponds with the example shown in the diagrams below -

-->-->-->Step to 14
Once u have made the necessary settings on your printer, the software will now temporarily disconnect your computer from your wire-less network & connect directly to your printer to configure the network settings.
Ur computer will re-connect to your wire-less network automatically once this has completed.

-->-->-->Step to 15
When the connection is established, click (Next) to continue with the software installation.

-->-->-->Step to 16
The printer driver software will now install & register onto your computer. This will take a few minutes to complete.

-->-->-->Step to 17
If this is the first time u're setting up your printer, it's recommended to perform the print head alignment. Click (Execute) to start the process & follow the on-screen instructions.
If u have already aligned the print head, click (Next).

-->-->-->Step to 18
Click (Execute) to perform a test print.
Once successfully printed, click (Next).

-->-->-->Step to 19
The set-up of your printer is now complete.
Click (Next) to see a list of optional software u can also install.

-->-->-->Step to 20
20 From the list select any additional software u wish to install & click (Next).

-->-->-->Step to 21
Once the additional software has installed, u will see a message informing u about setting up your smartphone or tablet. Click on (Instructions) to find out more information on setting up your device, or click (Next) to continue.

-->-->-->Step to 22
To register your printer, click (Next) (this will open in a web browser).
Alternatively, click (Skip).

-->-->-->Step to 23
Click (Exit) to finish the installation.

Connection For Mac users only

-->-->-->Step to 1
Double-click on the downloaded .dmg file to open the following screen.

Double-click on the (Setup) icon to start the setup. If the following screen appears, click (Open).

-->-->-->Step to 2
When the following screen appears, type your Password to allow the Helper Tool to be installed, then click on (Install Helper).

-->-->-->Step to 3
Click (Start Setup) .

-->-->-->Step to 4
The software will check to see if there are any updates to the driver & software & download them as necessary.

-->-->-->Step to 5
Select your region & country, then click (Next) .

-->-->-->Step to 6
If u accept the terms of the license agreement, click (Yes).

-->-->-->Step to 7
If u would like to take part in the extended survey program, click (Agree), otherwise click (Do not agree).

-->-->-->Step to 8
The following screen will briefly appear.

-->-->-->Step to 9
If your printer has already been connected to your wire-less network, u will see the following screen. Click (Yes) to continue with the installation & jump to -->-->-->Step to 17 . If your printer has not yet been connected please continue to -->-->-->Step to 10.

-->-->-->Step to 10
If your printer has not yet been connected to your wire-less network, u will see the following screen. Select wire-less LAN Connection, then click (Next).

-->-->-->Step to 11
Ensure that your printer is powered on & click (Next).

-->-->-->Step to 12
The software will search for any printers already set up on your network.

-->-->-->Step to 13
If this is the first time u're setting up your printer, it will not be displayed on the list.
Ensure (Set up the network connection according to the guide) is selected & click (Next) .

-->-->-->Step to 14
The set-up guide will open & guide u through connecting your printer to your network using the easy wire-less connect process.
Please follow the on-screen instructions carefully to prepare your printer for connection.
Only click next, when the printer corresponds with the example shown in the diagrams below.

-->-->-->Step to 15
The software will now temporarily disconnect your computer from your wire-less network & directly connect to your printer to configure the network settings.
Ur computer will re-connect to your wire-less network automatically once this has completed.
When the following message is displayed, click (Allow).

-->-->-->Step to 16
When the connection has successfully completed, click (Next).

-->-->-->Step to 17
The printer driver software will now install on to your computer.
This will take a few minutes to complete.

-->-->-->Step to 18
The software will now temporarily disconnect your computer from your wire-less network & directly connect to your printer to configure the network settings.
Ur computer will re-connect to your wire-less network automatically once this has completed.
If the following message is displayed, click (Allow).

-->-->-->Step to 19
Click (Add Printer) .

-->-->-->Step to 20
Select Canon 'MG/MX/TS/MP series' 'Bonjour Multifunction' from the list & click (Add) .

-->-->-->Step to 21
After adding your printer, the set-up screen may be hidden by the web browser. If this happens, click on the set-up icon set-up located in the dock, to display the screen again.
Once the printer has been added, click (Next) to continue.

-->-->-->Step to 22
If this is the first time u're setting up your printer, it's recommended to perform print head alignment. Click (Execute) to start the process & follow the on-screen instructions.
If u have already aligned the print head, click (Next).

-->-->-->Step to 23
Click (Start) to perform a test print & click (Print) .
Once successfully printed, click (Next).

-->-->-->Step to 24
The set-up of your printer is now complete.
Click (Next), to see a list of optional software u can also install.

-->-->-->Step to 25
From the list select any additional software u wish to install & click (Next).

-->-->-->Step to 26
Once the additional software has installed, u will see a message informing u about setting up your smartphone or tablet. Click (Instructions) to find out more information on setting up your device, or click (Next) to continue.

-->-->-->Step to 27
To register your printer, click (Next) (this will open in a web browser). Alternatively, click (Skip).

-->-->-->Step to 28
Once the additional software has installed, click (Exit) to finish the installation.
--------------------------------------------------------------------------------------------------------------------------

Restoring your printer’s network settings back to factory default

Restoring your printer’s network settings back to factory default. If u need to reset your network settings back to factory default, for example, if u change your access point, u can do so by following these instructions:

Please note that initialization erases all network settings on the machine, so printing or scanning from a computer over the network will become impossible until the printer is re-configured with new network settings.

-->-->-->Step to 1
Press & hold the (RESUME/CANCEL) button until the ALARM lamp flashes 19 times.

-->-->-->Step to 2
Release the (RESUME/CANCEL)

The network settings have been reset back to factory default settings.
Please now refer to the WiFi set-up – (WPS or Standard Connection methods) for instructions on setting up your printer onto your WiFi network.
Source of www.canon. co.uk

How to Scan epson stylus nx300

The Windows Fax & Scan utility enables u to scan doc & pictures. Before u can scan doc & pictures u must have a scanner installed on your computer. Your scanner must be listed in the Devices section of the Devices & Printers Control Panel window.
To check to see if your scanner is properly installed open the Device Stage. Choose Start→Devices & Printers. If Windows doesn’t automatically find your scanner u can manually add it in the Devices & Printers window by clicking the Add a Device button in the toolbar & following the wizard’s commands.
-->-->-->Step to 1
Choose Start→All Programs→Windows Fax & Scan.
Windows 7 opens the Windows Fax & Scan window.

-->-->-->Step to 2
Click the Scan button in the Navigation pane then click the New Scan button on the toolbar.
The New Scan dialog box for your scanner opens.

-->-->-->Step to 3
Use the settings on the right to describe your scan.
By letting the computer know what you’re scanning its color profile & the type of file u plan to create u enable Windows Fax & Scan to create the highest quality scan.

-->-->-->Step to 4
Click the Preview button to see what your doc will look like.
Make any last minute changes.

-->-->-->Step to 5
If you’re happy with the preview click the Scan button.
Windows scans the document & presents u with an image of your document.

-->-->-->Step to
Click the Save As button & complete the necessary information.
Enter the filename the type of graphics file u want to be saved & then click the Save button.
To automatically forward the document u have just scanned as an attachment to a new fax message click the Forward as Fax button.
The scan feature in the Windows Fax & Scan utility is set primarily to scan text documents. If u want to scan a photograph or other graphic you’re better off doing that directly within the Windows Live Photo Gallery.
The scan feature in the Windows Fax & Scan utility is set primarily to scan text documents. If u want to scan a photograph or other graphic you’re better off doing that directly within the Windows Live Photo Gallery.
Source of www.dummies .com

epson stylus nx300 Driver Download  & Software Download

epson stylus nx300 series Full Driver & Software Package
epson stylus nx300 series MP Drivers (Windows 10/10 x64/8.1/8.1 x64/8/8 x64/7/7 x64/Vista/Vista64/XP)x64/Vista/Vista64/XP)
epson stylus nx300 series Mini Master Setup (Windows 8.1/8.1 x64/8/8 x64/7/7 x64/Vista/Vista64/XP)
epson stylus nx300 series XPS Printer Driver (Windows 10/10 x64/8.1/8.1 x64/8/8 x64/7/7 x64/Vista/Vista64/XP)x64/Vista/Vista64/XP)
brother ads-2600we Easy-PhotoPrint EX (Windows 10/10 x64/8.1/8.1 x64/8/8 x64/7/7 x64/Vista/Vista64/XP)x64/Vista/Vista64/XP)
epson stylus nx300 My Image Garden (Windows 10/10 x64/8.1/8.1 x64/8/8 x64/7/7 x64/Vista/Vista64/XP)x64/Vista/Vista64/XP)
epson stylus nx300 Quick Menu (Windows 10/10 x64/8.1/8.1 x64/8/8 x64/7/7 x64/Vista/Vista64/XP)x64/Vista/Vista64/XP)
epson stylus nx300 My Printer (Windows 10/10 x64/8.1/8.1 x64/8/8 x64/7/7 x64/Vista/Vista64/XP)x64/Vista/Vista64/XP)
epson stylus nx300 series Full Driver & Software Package - (Mac Os )
epson stylus nx300 series CUPS Printer Driver - (Mac Os)
epson stylus nx300 ICA Driver - (Mac Os)
Setup :
Step-to-Install
Click to 'DOWNLOAD'
Plug-in-cable printer to Device
Click Open File
Double click on the downloaded file
Then Restart your Device
Good luck.

Step-to-Uninstall
Open the control panel of your device
Click uninstall
Double click on the driver file you want to uninstall
Follow the instructions uninstallation
click Finish
Good luck.

Epson stylus nx300 Wireless Printer Setup, Software & Driver Rating: 4.5 Posted by : Wireless Printer Setup
Posted by : Wireless Printer Setup - Wireless Printer Setup Updated at : October 19, 2018